General description
The TIS700 series for automotive transient unifies the capabilities of an EFT/Burst simulator, a micro pulse simulator and the required coupling network into one box. The TIS700 series are equipped to meet all international and car manufacturer specifications. The current of built-in coupling network ranges up to 100Adepending on the model. The built-in coupling network can be used and controlled by any unit of the LDS200 series, APG series and APS series. For tests beyond standard’s requirements the waveform parameters of the micro pulse generator can be varied in a wide range by means of the freestyle mode.
Features
5.7 inch color touch screen
Built-in EFT/Burst generator module
Built-in micro pulse generator module, as per ISO 7637, JASO, SAE and NISSAN
Built-in coupling network 60V, up to 100A
With the function of current detection and over current protection
Emergency stop
Built-in battery switch
Ethernet, RJ45 connector, PC control and test report documentation and print
|
Technical Data |
|||||||
|
Micro pulse module for test P1/2a |
|||||||
|
Test voltage |
30 – 600V |
||||||
|
Polarity |
Positive/negative |
||||||
|
Pulse wave form |
1us/50us, 1us/2ms, 3us/1ms |
||||||
|
Rise time Tr |
0.5us – 1us, 1.5us – 3us without load |
||||||
|
Duration Td |
50us ±20% without load 12us ±20% without load 1ms ±20% without load 1ms ±20% with 50 ohm load 2ms ±20% without load 1.5ns ±20% with 10 ohm load
0.2ms 土20% without load 0.3ms 土20% without load 0.5ms土20% without load
|
||||||
|
Source impedance |
2ohm, 4ohm,10 ohm, 30 ohm, 50 ohm |
||||||
|
Test times |
1 - 9999 |
||||||
|
DUT voltage monitoring |
10:1 |
||||||
|
DUT current monitoring |
10A:1V |
||||||
|
Pulse interval |
0.2s – 60s |
||||||
|
trigger |
Automatic |
Automatic release of the pulses |
|||||
|
Manual |
Manual release of a single pulse |
||||||
|
External |
External release of a single pulse |
||||||
|
Battery switch trigger |
0 – 10000ms off time, selectable, |
||||||
|
output |
DUT supply |
central DUT output |
|||||
|
coupling |
to the battery line |
||||||
|
decoupling |
via diode and battery supply switch |
||||||
|
serial connector |
LAN Ethernet RJ45 |
||||||
|
external trigger |
trigger occurs when the connector is closed; BNC connector |
||||||
|
Technical Data |
|||||||
|
EFT/ burst module for test pulse3a/3b |
|||||||
|
Test voltage |
25 – 700V |
||||||
|
Polarity |
Positive/negative |
||||||
|
Pulse wave form |
5/150ns into 50 ohm and 1000 ohm load |
||||||
|
Rise time Tr |
5ns±30% into 50 ohm load |
||||||
|
5ns±30% into 1000 ohm load |
|||||||
|
Duration Td |
150ns – 45/+45ns into 50 ohm load |
||||||
|
150ns – 45/+45ns into 1000 ohm load |
|||||||
|
Source impedance |
50 ohm |
||||||
|
Pulse |
1- 200 |
||||||
|
Test and Control (trigger circuit) |
|||||||
|
Trigger of bursts |
Automatic, manual, external |
||||||
|
Burst duration |
50ms – 999ms |
||||||
|
Test duration |
1s-50000s | ||||||
|
Pulse frequency |
0.1kHz – 200kHz |
||||||
|
|
|
||||||
|
|
|||||||
|
Output |
Direct output |
Via 50 ohm coaxial connector (for tests using e.g. a capacitive coupling clamp) |
|||||
|
Coupling mode |
To the battery line(supply lines) |
||||||
|
CRO trigger |
5V trigger signal for oscilloscope |
||||||
|
General Data |
|||||||
|
power supply |
AC 110/220V, ±10%, 45-65Hz |
||||||
|
temperature |
15-+35 ℃ |
||||||
|
humidity |
35%- 85% RH (no condensation) |
||||||
|
size |
450×600×177mm(4U cabinet) |
||||||
|
Weight |
20kg |
||||||
|
network |
built-in 60V/50A,75A,100Acoupling/decoupling network short impulse overcurrent capacity is more than 200ms |
||||||
|
input |
DUT supply |
DC from APS or APG series |
|||||
|
pulse 5 |
DUT supply |
||||||
|
output |
input from LDS200 |
central DUT output terminal |
|||||
|
coaxial output terminal |
connect with capacitive coupling clamp(as per ISO 7637-3:2007) |
||||||
|
Basic equipment |
|||||||
|
simulator, user manual, test report, warranty book, test cable, power cord, DUT power cord, ground wire, user test program, standard test program(level 1-4 as per ISO 7637-2:2011) |
|||||||
|
optional accessories |
capacitive coupling clamp |
||||||
|
load resistance for pulse calibration |
|||||||
|
Software(optional) |
|||||||
|
Software AUTO Lab for software With PC installed WIN XP and WIN7, it can be easily operated to make the measurement, based on the customized test program. It can identify any device for AUTO Lab test with automatic configuration. It can easily generate test reports. |
|||||||
